cmdline.txt
· 311 B · Text
Raw
# Modified cmdline.txt for CutiePi. Replace PARTUUID with your own (use `sudo blkid` or `ls -l /dev/disk/by-partuuid/` to find it).
root=PARTUUID=750709b2-02 rw rootwait console=tty1 selinux=0 fsck.repair=yes plymouth.ignore-serial-consoles smsc95xx.turbo_mode=N dwc_otg.lpm_enable=0 usbhid.mousepoll=8 audit=0
| 1 | # Modified cmdline.txt for CutiePi. Replace PARTUUID with your own (use `sudo blkid` or `ls -l /dev/disk/by-partuuid/` to find it). |
| 2 | root=PARTUUID=750709b2-02 rw rootwait console=tty1 selinux=0 fsck.repair=yes plymouth.ignore-serial-consoles smsc95xx.turbo_mode=N dwc_otg.lpm_enable=0 usbhid.mousepoll=8 audit=0 |
| 3 |
config.txt
· 2.1 KiB · Text
Raw
### Modified version of /boot/config.txt for CutiePi
# See /boot/overlays/README for all available options
# Uncomment some or all of these to enable optional Hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Run in 64bit mode
arm_64bit=1
# Auto load correct initramfs files if found
auto_initramfs=1
# Run as fast as the firmware/board allows
arm_boost=1
# Disable compensation for displays with overscan
disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# Enable sound
dtparam=audio=on
# Uncomment if no sound thru hdmi
#hdmi_drive=2
# Auto load overlays for detected cameras
camera_auto_detect=1
# Auto load overlays for detected DSI displays
display_auto_detect=1
# Enable DRM VC4 V3D driver
#dtoverlay=vc4-kms-v3d
# For pi4's and above boards uncomment next line & Comment out above line
dtoverlay=vc4-kms-v3d,cma-512
max_framebuffers=2
# Don't have the firmware create an initial video= setting in cmdline.txt
# Use the kernel default instead
#disable_fw_kms_setup=1
# Disable rainbow screen at boot
disable_splash=1
# RPi 5B/4B/400 ONLY
# For 4k content @ 60 Hz refresh rate, uncomment hdmi_enable_4kp60=1
#hdmi_enable_4kp60=1
# If video breaks with hdmi_enable_4kp60=1 uncomment
#force_turbo=1
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller
# This line should be remoed if the legacy DWC2 controller is required
otg_mode=1
avoid_warnings=2
dtoverlay=cutiepi-panel
enable_uart=1
dtoverlay=uart1
dtoverlay=i2c5,pins_10_11
dtoverlay=mpu6050-i2c5,interrupt=27
start_x=1
gpu_mem=128
dtoverlay=ov5647
[all]
| 1 | ### Modified version of /boot/config.txt for CutiePi |
| 2 | |
| 3 | # See /boot/overlays/README for all available options |
| 4 | |
| 5 | # Uncomment some or all of these to enable optional Hardware interfaces |
| 6 | dtparam=i2c_arm=on |
| 7 | #dtparam=i2s=on |
| 8 | #dtparam=spi=on |
| 9 | |
| 10 | # Run in 64bit mode |
| 11 | arm_64bit=1 |
| 12 | |
| 13 | # Auto load correct initramfs files if found |
| 14 | auto_initramfs=1 |
| 15 | |
| 16 | # Run as fast as the firmware/board allows |
| 17 | arm_boost=1 |
| 18 | |
| 19 | # Disable compensation for displays with overscan |
| 20 | disable_overscan=1 |
| 21 | |
| 22 | # uncomment the following to adjust overscan. Use positive numbers if console |
| 23 | # goes off screen, and negative if there is too much border |
| 24 | #overscan_left=16 |
| 25 | #overscan_right=16 |
| 26 | #overscan_top=16 |
| 27 | #overscan_bottom=16 |
| 28 | |
| 29 | # uncomment to force a console size. By default it will be display's size minus |
| 30 | # overscan. |
| 31 | #framebuffer_width=1280 |
| 32 | #framebuffer_height=720 |
| 33 | |
| 34 | # uncomment if hdmi display is not detected and composite is being output |
| 35 | #hdmi_force_hotplug=1 |
| 36 | |
| 37 | # uncomment to force a specific HDMI mode (this will force VGA) |
| 38 | #hdmi_group=1 |
| 39 | #hdmi_mode=1 |
| 40 | |
| 41 | # Enable sound |
| 42 | dtparam=audio=on |
| 43 | # Uncomment if no sound thru hdmi |
| 44 | #hdmi_drive=2 |
| 45 | |
| 46 | # Auto load overlays for detected cameras |
| 47 | camera_auto_detect=1 |
| 48 | # Auto load overlays for detected DSI displays |
| 49 | display_auto_detect=1 |
| 50 | |
| 51 | # Enable DRM VC4 V3D driver |
| 52 | #dtoverlay=vc4-kms-v3d |
| 53 | # For pi4's and above boards uncomment next line & Comment out above line |
| 54 | dtoverlay=vc4-kms-v3d,cma-512 |
| 55 | max_framebuffers=2 |
| 56 | |
| 57 | # Don't have the firmware create an initial video= setting in cmdline.txt |
| 58 | # Use the kernel default instead |
| 59 | #disable_fw_kms_setup=1 |
| 60 | |
| 61 | # Disable rainbow screen at boot |
| 62 | disable_splash=1 |
| 63 | |
| 64 | # RPi 5B/4B/400 ONLY |
| 65 | # For 4k content @ 60 Hz refresh rate, uncomment hdmi_enable_4kp60=1 |
| 66 | #hdmi_enable_4kp60=1 |
| 67 | # If video breaks with hdmi_enable_4kp60=1 uncomment |
| 68 | #force_turbo=1 |
| 69 | |
| 70 | # Uncomment this to enable infrared communication. |
| 71 | #dtoverlay=gpio-ir,gpio_pin=17 |
| 72 | #dtoverlay=gpio-ir-tx,gpio_pin=18 |
| 73 | |
| 74 | [cm4] |
| 75 | # Enable host mode on the 2711 built-in XHCI USB controller |
| 76 | # This line should be remoed if the legacy DWC2 controller is required |
| 77 | otg_mode=1 |
| 78 | avoid_warnings=2 |
| 79 | |
| 80 | dtoverlay=cutiepi-panel |
| 81 | enable_uart=1 |
| 82 | dtoverlay=uart1 |
| 83 | dtoverlay=i2c5,pins_10_11 |
| 84 | dtoverlay=mpu6050-i2c5,interrupt=27 |
| 85 | |
| 86 | start_x=1 |
| 87 | gpu_mem=128 |
| 88 | dtoverlay=ov5647 |
| 89 | |
| 90 | |
| 91 | [all] |
| 92 |